Step	System	Action
1.	INS	ALIGN or NAV
2.	Target alt/range knob	170
3.	ARBCS bombing timers	SET
	a. Pullup	5.0
	b. Release	10.0
4.	(P) BRG/DIST switch	NAV COMP
5.	(WSO) Nav mode switch	NAV COMP

Step	System	Action
1.	WRCS BIT selector	LAYDOWN
2.	BIT button	PUSH and HOLD
3.	After 5 seconds, FRZ button.	PUSH ON
	a. Range indicator	ON
	b. After 15 seconds	GO/NO GO

Step	System	Action
1.	WRCS BIT selector	DIVE LAYDOWN
2.	BIT button	PUSH and HOLD
3.	After 5 seconds, FRZ button.	PUSH ON
	a. Alt indicator	ON
	b. After 15 seconds	GO/NO GO

Step	System	Action
1.	WRCS BIT selector	DIVE TOSS
2.	BIT button	PUSH and HOLD
3.	After 5 seconds, FRZ button.	PUSH ON
	a. Alt indicator	ON
	b. After 15 seconds	GO/NO GO

Step	System	Action
1.	WRCS BIT selector	AGM-45
2.	BIT button	PUSH and HOLD
	a. BDHI and HSI miles 7.6 ± 1.0 NM
	b. Alt indicator	ON
3.	After 5 seconds, FRZ button.	PUSH ON
	a. BDHI and HSI miles DECREASE
	b. AOA lower indexer	PULL UP COMMAND
	c. After 10 seconds, AOA center indexer	LEVEL COMMAND
	d. After 5 seconds	GO/NO GO
	e. After 5 seconds, AOA upper indexer	DIVE COMMAND

Step	System	Action
1.	WRCS BIT selector	TGT FIND/OFFSET BOMB
2.	BIT button	PUSH and HOLD
	a. Alt indicator	ON
3.	After 5 seconds, along track cursor control	MOVE
4.	Cross track control	MOVE
5.	Cursor intensity	ADJUST
6.	Reset button	PUSH
	a. Cursors return to zero range and azimuth.
7.	Target insert button	PUSH ON
	a. Along track cursor	6.5 NM on 00 grid line (±.2000 feet)
	b. Cross track cursor	30° +1.5° RIGHT
	c. (P) HSI bearing pointer	23° ±.2.5° (right of lubber); HSI TGT light - ON
	d. TGT INS light	ON
	e. BDHI #1 needle	23° ±.5° (right of top index)
	f. (P-WSO) HSI and BDHI miles	4.8±.1.0 NM
	g. (P) Sight roll tabs	ROTATED CLOCKWISE
	h. (P) ADI vertical pointer	DEFLECTS FULL RIGHT
8.	After 5 seconds, FRZ button.	PUSH ON
	a. (P-WSO) HSI and BDHI miles	DECREASE TO ZERO, THEN INCREASE
	b. (P) Sight roll tabs	ROTATES (as miles passes through zero)
	c. After 15 seconds	GO/NO GO

Step	System	Action
1.	INS mode	NAV
2.	WRCS control panel	SET
	a. Target distance N/S	N120
	b. Target distance E/W	000
	c. Target altitude	SET PRESENT AIRCRAFT HSL (29.92)
	d. Release advance	000
	e. Release range	000
3.	Weapons delivery panel	SET
	a. Activate switch	NORM
	b. Target find switch	HOLD
	c. Range switch	X100
4.	Front cockpit switches	SET
	a. Delivery mode	T LAD
	b. Weapon select	BOMBS
	c. Station select buttons	OFF
	d. Armament override	PUSH IN
5.	Timers	SET (values for delivery)
	a. Pullup timer
	b. Release timer
6.	Target insert button	PUSH ON
	a. Along track cursor	Jumps to second BIT target
7.	WRCS distance counters N/S	Increase or decrease until near edges of along track cursor and second BIT target coincide.
	a. Note difference between counter and N120.
	b. For larger counter value, correction is +; for smaller counter value the correction is -.
8.	Target distance N/S	RESET
	a. Set preflight release range adjusted for calibration error in step 7.
	b. Release range switch	NORM or X100 (as required)
	c. Activate switch	ON
9.	Release range counter	INCREASE (slowly until 1/3 second tone)
	a. Check timer accuracy.
	b. (P) Check LABS indications.
	c. Note difference between derived RR counter reading and preflight release/activation range and apply as correction to all ranges.
	(1) For larger counter value, correction is+; for smaller counter value, the correction is-.

Step	System	Action
1.	WRCS BIT selector	RELEASE and OFF
2.	Target alt/range counter	000
3.	Weapons delivery panel
	a. Activate switch	NORM
	b. Target find switch	NORM
	c. Range switch	NORM
4.	WRCS control panel	RESET